Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
The content listed below pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is relatively fascinating. Don't miss out on it.
![How to Install a Bathtub: Install an Acrylic Tub and Tub Surround](https://www.impressiveinteriordesign.com/wp-content/uploads/2020/05/installing.jpg)
Setting up a bathtub isn't exactly brain surgery, yet it does call for solid plumbing, woodworking, and often, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is readily accessible, the task can relocate rapidly; if you have to open up a wall surface to get rid of the old bathtub and place the brand-new tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will require an assistant to move out the old bathtub as well as embeded in the new one. Make sure you have actually certified yourself for the task and also are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed task, it is better to consider using one before you start. Opportunities are you might need a specialist plumber to make tube links.
This write-up will aid you mount a brand-new bath tub in your shower room if you have currently gotten a brand-new tub as well as don't need to alter the setup of your previous supply of water pipes.
Your devices and material checklist need to make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing taps can be quite bothersome due to the limited access that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a fabric ready for the remaining water that will come from the pipes. Once the supply pipes have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to carrying on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing hole in the bath/basin making sure that the washing machines remain in place in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap ports. The former type ought to be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Making use of the two wood boards under its feet, position the bath tub in the needed position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to make certain that the tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bath tub up until the spirit level reads degree.
To install faucets, fit all-time low of the furthest versatile tap port to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Turn on the water system as well as inspect all joints and new pipework for leaks and tighten them if necessary. Fill up the bathtub as well as additionally inspect the overflow electrical outlet and the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the producer's instruction manual. Tiling and securing around the bath tub should wait until the bathtub has been utilized a minimum of once as this will certainly resolve it right into its final setting.
Planning for the Installment
First of all, the supporting framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps unit to stop stress on the bath tub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last position.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture an inflexible seal, causing the water to pass through the wall in between the bathroom and the tiling, leading to problems with dampness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealer can fracture fairly early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily offered on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
![A Step-by-Step Guide to Installing a Bathtub](http://hak.gwc134.net/Other/buangi%20lane/20090110_bathroom_3.jpg)
I came across that blog posting about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while perusing the internet. Do you know about anybody else who is very much interested in the subject? Why not share it. Thank you for your time. Kindly pay a visit to our website back soon.
Quick help? Contact. Report this page